HolyBro Kakute F7 HDV Flight Controller
  • HolyBro Kakute F7 HDV Flight Controller
  • HolyBro Kakute F7 HDV Flight Controller
  • HolyBro Kakute F7 HDV Flight Controller
  • HolyBro Kakute F7 HDV Flight Controller
  • HolyBro Kakute F7 HDV Flight Controller

HolyBro Kakute F7 HDV Flight Controller

45,90 €
Tasse incluse

Acquistando questo prodotto puoi ricevere fino a 4 punto punti. Il tuo carrello ti offrirà 4 punti convertibili in un voucher di: 0,40 €.

HolyBro Kakute F7 HDV is designed to work with the DJI FPV VTx module. The GH port available on the board makes it much more convenient for you to connect HolyBro Kakute F7 HDV to the DJI FPV VTx, for both signal and power supply.

Quantità
CONTROLLO QUANTITÀ:

Non ordinabile
 

RIVENDITORI UFFICIALI - Garanzia ITALIA 24 mesi

 

Spedizione LAMPO entro 24/48h se il prodotto è disponibile

 

Un esperto sempre al tuo servizio!

Overview
HolyBro Kakute F7 HDV is designed to work with the DJI FPV VTx module. The GH port available on the board makes it much more convenient for you to connect HolyBro Kakute F7 HDV to the DJI FPV VTx, for both signal and power supply.

Features

  • Supports Betaflight, Butterflight, and Cleanflight.
  • High-performance / low-noise IMU. MPU6000 with 6-axis gyro and accelerometer.
  • Ready for autonomous flight: Integrated BMP280 barometer and SCL/SDA for use with external GPS/magnetometer units.
  • Dedicated bootloader button for easy firmware flashing.
  • Low-profile design fits into even very compact frames.
  • Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on “B+” pad only).
  • Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the KAKUTE F7 HDV monitors voltage directly from the power supply.
  • Filtered voltage output for clean, noise-free video. 2 On-board regulators output 5V and 8V. 5V output up to 1.5A to power peripherals such as receiver, FPV camera, or LED strip. 8V output up to 2A to DJI FPV VTx.
  • Supports BLHeli pass-through for easy ESC upgrade and configuration.

Specifications

  • MCU: STM32F745 32-bit processor
  • IMU:MPU6000
  • Barometer: BMP280
  • USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
  • 6 hardware UARTS (UART1,2,3,4,6,7)
  • All UARTS support hardware inversion. SBUS, SmartPort, and other inverted protocols work on any UART without “uninvert hack”.
  • Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.
  • TF card for Blackbox logging
  • Dimensions: 35x35mm
  • Mounting Holes: Standard 30.5mm square to center of holes
  • Weight: 8g

Package Includes:
FC board *1
M3 Damping Ball*4
JST SH 8pin 150mm cable*1
JST GHR 8pin to JST GHR 6pin 80mm cable*1

Manual:
Holybro Kakute F7 HDV Manual

Chatta con noi su Whatsapp